Page 19 of 22
Re: It lives
Posted: Sun Mar 27, 2016 9:15 pm
by RGV
Nice work Greg, yep im just going to use mild steel filler rod. Ill cut out the sides tomorrow and post up some pics as i go.
Dave
Re: It lives
Posted: Mon Mar 28, 2016 8:15 pm
by RGV
Tank is tacked together, need to make mounts then start welding.
The tank its replacing.
Dave
Re: It lives
Posted: Tue Mar 29, 2016 7:44 pm
by RGV
Welded, just the mounts to go. There made will weld them on tomorrow then I can get on with the making the swing arm and lowering the seat/rear end mount.
Dave
Re: It lives
Posted: Fri Apr 01, 2016 9:44 pm
by Greg Watters
Thats come up real good , lots less filler than i needed
Re: It lives
Posted: Fri Apr 01, 2016 9:57 pm
by RGV
Thanx Greg, yep im happy with it so far. Ive made a recess to fit into the top so I can get my helmet 50 mm lower. Just imagine it up the other way LOL. I wont fit it till ive got my seat and peg position finalized. Once thats welded in I will be able to pressure test it. Then the fun begins, fixing the pin holes. Might just put a tank liner in if its too bad.
Dave
Re: It lives
Posted: Sun Apr 03, 2016 10:53 am
by BONES
Looks good Dave
Are you any good with aluminium ?
The steering head is 750 from the ground but there is a little more to be gained with the USD-- 30mm . It all counts
I machined the OD of the fork legs on the bussa so I could slide them further through the lower triple clamp. Internally they are
parallel .
cheers Bones
Re: It lives
Posted: Sun Apr 03, 2016 6:50 pm
by RGV
Hey Bones, I havnt tried alloy as I dont have the equipment to weld it. From what ive heard its easier to work than steel. This was some of what I had left over from making my chambers. Still have to make a new air box as the old one i made used the original tank as the top. Ill do the same with this one.
I reckon with my lower profile tyre and dropping the forks ill get at least 25mm.
Dave
Re: It lives
Posted: Thu Apr 14, 2016 10:35 am
by RGV
Re: It lives
Posted: Sat Feb 04, 2017 5:04 pm
by RGV
Quick update. Bike is running and lowered with the low tank installed. I didnt fit the longer swing arm as I didnt want to do 2 fairly major changes. If it doesn't handle as well as it did I will know what the cause is.
Dave
Re: It lives
Posted: Wed Feb 08, 2017 12:25 am
by SlowRobo
She looks very nice Dave... tank very stylish.
I thought the last time we talked you were going to give FUEL away. U just a tiger for punishment.
I fired my little Aprilia up today. it runs sweet as a nut. I leave today fortnight.
#1215 Salt Smoker.
Re: It lives
Posted: Thu Feb 09, 2017 5:30 pm
by RGV
Im not running Methanol this time, some Sunoco stuff. Its got some ethanol in it but should tune much like Gas.
Ive gone back to an engine that I know (Hope) works so just aero changes really to my old Gas bike.
Good to hear the Ape is up and running. Have a safe trip.
Dave
Re: It lives
Posted: Sat Aug 05, 2017 11:23 pm
by RGV
So ive been thinking about what I am doing wrong with my last tuning attempts. Checked all the ignition and jetting and cant put my finger on what i have missed. Ive made quite a few changes, new pipes, modded carbys for methanol and ignition changes. The pipes are copied from a known good set (Thanx to Pete) Ignition will be reset to a known good setting and a pair of new carbys have been ordered. New pistons are next on the list.
Ive also been thinking about my heads. The O rings were always looking like they were about to fail, after some Googling it dawned on me that I had them skimmed to check the flatness, 0.2 was removed leaving the groove to take the O ring too small. I will get the groove machined to the right size.
Dave
Re: It lives
Posted: Tue Aug 29, 2017 7:22 pm
by RGV
New carbs arrived, waiting on pistons then its time to put it back together ready for another try.
Dave
Re: It lives
Posted: Sun Sep 10, 2017 12:20 am
by simpleterm
Hey there, I don't know if this is possible, but do you have the photos before Photobucket started going crazy, so you can upload them somewhere where I could see them? Thank you! I know this may take some time, and I understand if this is not at all possible. Good luck, though!
Re: It lives
Posted: Sun Sep 10, 2017 6:46 pm
by RGV
If you are using Google Chrome there is an extension that you can enable that will make it possible to view the Photo Bucket pics. Works fine for me.
https://chrome.google.com/webstore/sear ... link?hl=en
Dave