Mals Effie project

See cars and bikes being built for the salt

Moderator: DLRA

momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

Depends on how far the head is located relative to the bum I spose.
Chris
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

Well, this week was spent thinking. Seem to do a lot of that when attacking the salt again.
I'm sure ever salt racer would agree, we spend more time thinking and planning the project than actually working on it. Too much time to think.

Thoughts this week have concentrated on radiator position and scoop design.
When we built the Effie there was no rule on radiator position. Taking this grey area I fitted an ex Supercar radiator (quite short) as low as possible then built an airbox to pickup from above the radiator. A win/win. No scoop through the bonnet.

Well, the rule changed to specify "Radiator mounted at stock height and position". Nothing grey there anymore.
I think our only possible choice to achieve positive airbox pressure will be to poke a scoop though the bonnet.
Ok that was this week.
Solved a problem, made a decision. Tick.
Chris
User avatar
RGV
Posts: 708
Joined: Sun Feb 06, 2011 9:17 pm
Location: Mid Murray Mallee

Re: Mals Effie project

Post by RGV »

Does it mention the bottom of the radiator being in the stock position? Could you lift the rad to the original height but use the short rad and bring the air in underneath?

Dave

Last Minute Racing
DLRA #928

2010 MPS/G 250 118 MPH
2011 Washed Out
2012 Washed Out
2013 MPS/G 250 131 MPH (RECORD)
2014 MPS/G 250 140 MPH (RECORD)
2015 MPS/F 250 DNF
2016 MPS/F 250 114 MPH (RECORD)
2017 MPS/F 250 DNF
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

Thought of that too Dave, no can do.
Also the air intake height can't be lower than the original pickup point.
No other stock holes high in the rad support panel that would suit. I don't wont to use cowl induction as I cant be convinced it will create positive pressure.
Chris
User avatar
JonB
Posts: 268
Joined: Wed Oct 06, 2010 6:35 pm
Location: Brisbane

Re: Mals Effie project

Post by JonB »

Chris
I have used rearward facing bonnet scoops on road cars successfully.
No actual numbers other than a HJ with 253 5 speed rearward facing scoop would loose about 15kph top speed when I took the sealing ring between the bonnet and the air cleaner housing off.
Had a Carter Thermoquad (XD Cleveland) and Cleveland air cleaner housing with the original inlet hole blocked off and the lid cut at the diameter of the air cleaner element.

Why Ford stuff on a Holden?, XD ute was my toy at the time, HJ family car.
Carter Thermoquads greatly underrated IMHO.

Had cowl induction on the XD, never did back to back runs as it was a pig to pull the connecting hoses off.

Just my 2c
Jon

Not working on my liner at the moment, distracted by a longer slower ride.
Bored at a rest day in Coober Pedy.
DLRA#1115
Underhouse Engineering
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

Fantastic to hear from you Jon, so your still pedalling strong? Any major problems. Cooper Pedy would seem like New York after where you've been :wink:

Could tune a thermoquad on a dyno almost as well as any efi system if you spend enough time.
Ran cowl induction on the XP ute and the incar clearly shows. https://www.youtube.com/watch?v=cl7QZTncQXc the top of the scoop being sucked down .
I cannot be convinced they create + pressure.
Chris
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

Bob Ellis dropped around yesterday morn to give Bridgee and I a run through on what we had to do to run Bonneville.

Well bottom line, need some changes to the cage we weren't planning but, so be it. Our tube wall thickness was a bit under. Need to shift the battery cut off to the rear panel. Vent the battery box and isolate it from the fuel cell. Change chute mounting.

I want to fit the full containment seat and shift it closer to the centre. Shift column across to match. Redesign the window net from scratch so it is compact, easy to use and effective. I'm guessing this part alone will be time consuming to get right.
Change throttle cable to a morse type.
This plus the major rework to lower suspension, reposition the engine and trans etc etc.
Going to get real busy soon.
Chris
OLDtimer
Posts: 381
Joined: Sat Jan 05, 2008 5:56 pm
Location: Eyre, South Australia.

Re: Mals Effie project

Post by OLDtimer »

Chris, that proves that Holden motors suck when you put 'em in fords
Pete.
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

Pete, the F Truck runs in production. She runs different size Windsors.
This time will be a 301ci
Chris
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

Progress happens,

Cage removed last week and nutted out shape for new one including funny car style drivers surrounds. We are shifting the driver inboard a bit to make more clearance from the window net. Next will be the major lowering job, adjustable front struts and heavier rear springs.


Keep you posted.
Chris
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

http://i1120.photobucket.com/albums/l49 ... 5871329679
Ok, this is the old F Truck.
New one will be lower.
Chris
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

So why is this photo thing so bloody impossible. Put the pic in photo bucket. Click the URL thing above. Copy your pic then post in between the . What have I done wrong. The previous post ends up with a link not a pic.

Help.
Chris
User avatar
RGV
Posts: 708
Joined: Sun Feb 06, 2011 9:17 pm
Location: Mid Murray Mallee

Re: Mals Effie project

Post by RGV »

In Photo bucket on the right side "Share Links" bottom line "IMG" left click it, it says "copied" Right click in ya post and paste. I Think thats how I did it.

Dave

Image

Last Minute Racing
DLRA #928

2010 MPS/G 250 118 MPH
2011 Washed Out
2012 Washed Out
2013 MPS/G 250 131 MPH (RECORD)
2014 MPS/G 250 140 MPH (RECORD)
2015 MPS/F 250 DNF
2016 MPS/F 250 114 MPH (RECORD)
2017 MPS/F 250 DNF
momec3
Posts: 780
Joined: Tue Mar 01, 2011 10:36 pm
Location: Cedar Grove Qld

Re: Mals Effie project

Post by momec3 »

Cool, got it. thanks Dave
Chris
Post Reply