Commodore Valuables
Moderator: DLRA
Doctor,
Did'nt realise there were no solid rollers available for the V6?
Can probally supply you with some free used LS lifters that are past there use by. Will check supply Monday. PM me if you want them. Converting to a solid is fine providing you can get them apart. Just chuck the squashy parts and make a solid replacement.
Mostly l deal with solid rollers and all Chevs, Holdens and Fords provide oil up the pushrods for rocker lube.
Normally we fit restrictors in the oil gallery on the supply side when solids are fitted.
Most currant Supercars are now using keyed Jesel lifters and all have bushed lifter bores with individual restrictors. We have just finished a 7000km Spintron test for V8SC running simulated laps of Bathurst.
This was for the new control cam they have mandated from this weekend at Darwin.
To check the oil supply window to your chosen lifter fit desired cam in block.
Remove oil gallery bung, (usually at rear) and drop chosen lifter in closest hole.
With torch peir down gallery and you should be looking at the hole lining up with the gallery.
Rotate cam by hand and make sure the hole stays in the window for a majority if not the whole rotation.
If it misses a lot you can slot the side of the lifter to give supply to the hole.
Some motors this process is not that easy and you have to do it mathmatically.
Race motor solid roller ducks guts good luck.
Chris
Did'nt realise there were no solid rollers available for the V6?
Can probally supply you with some free used LS lifters that are past there use by. Will check supply Monday. PM me if you want them. Converting to a solid is fine providing you can get them apart. Just chuck the squashy parts and make a solid replacement.
Mostly l deal with solid rollers and all Chevs, Holdens and Fords provide oil up the pushrods for rocker lube.
Normally we fit restrictors in the oil gallery on the supply side when solids are fitted.
Most currant Supercars are now using keyed Jesel lifters and all have bushed lifter bores with individual restrictors. We have just finished a 7000km Spintron test for V8SC running simulated laps of Bathurst.
This was for the new control cam they have mandated from this weekend at Darwin.
To check the oil supply window to your chosen lifter fit desired cam in block.
Remove oil gallery bung, (usually at rear) and drop chosen lifter in closest hole.
With torch peir down gallery and you should be looking at the hole lining up with the gallery.
Rotate cam by hand and make sure the hole stays in the window for a majority if not the whole rotation.
If it misses a lot you can slot the side of the lifter to give supply to the hole.
Some motors this process is not that easy and you have to do it mathmatically.
Race motor solid roller ducks guts good luck.
Chris
Acme Racing #251
-
- Posts: 1315
- Joined: Tue Jul 05, 2005 11:23 pm
- Location: Right behind you Chief !
dub
Jeez if you were going to fiddle with it like that you could have at least dubbed over the sound of it leaving the line missing like a bastard I'll see you during the week.....
Now, in other news for the Spirit of Sunshine I hoisted the motor today and cracked off the box. The motor is an auto crank version as some will remember. When I got to the flywheel it was loose, again. The cap heads securing the crank adapter had a full turn each on them....the adapter had also galled against the end of the crank. I'm done muckin around with this adapter, we want to rev the motor harder and I don't want the flywheel to come off so I've found a manual crank , we'll get it balanced with the flywheel and we'll be able to sleep a little easier......
Oh yeah and I emptied the contents of the gearbox all-over the floor, like a dickhead...I tipped it over to work on the selectors and then left for an hour or so....when I came back the breather tube was hanging down and it was kitty-litter time
As for a "spintron" my brain has been in hyperdrive about all this for the last couple of weeks and I'm not sure which night at 3am it started but for the last few days I've been thinking it'd be bloody great to have a way of running the top end of the motor AND the oiling system up to 8000rpm without the crank and pistons.....that'd make this development stuff a whole lot easier.......in my dreams....
Now, in other news for the Spirit of Sunshine I hoisted the motor today and cracked off the box. The motor is an auto crank version as some will remember. When I got to the flywheel it was loose, again. The cap heads securing the crank adapter had a full turn each on them....the adapter had also galled against the end of the crank. I'm done muckin around with this adapter, we want to rev the motor harder and I don't want the flywheel to come off so I've found a manual crank , we'll get it balanced with the flywheel and we'll be able to sleep a little easier......
Oh yeah and I emptied the contents of the gearbox all-over the floor, like a dickhead...I tipped it over to work on the selectors and then left for an hour or so....when I came back the breather tube was hanging down and it was kitty-litter time
We have the poor cousin VN series 1 Chris , which is like the grey motor.... The attraction of modding the standard ones is that the oiling is right, as stated earlier they have a chamfer that lets the oil at them after the hole goes above the gallery, restriction wise drilling a smaller hole in the other side and soldering up the original one looks to be the safest option. Greg Watters pointed out that if we do bung up the standard ones it would be safer to use a proper circlip in the top than the pissy hairclip they have in them....he also felt that if we used a piece of short tube that it would be better above than below the original piston.....Handy Hano wrote:Doctor,
Did'nt realise there were no solid rollers available for the V6?
Can probally supply you with some free used LS lifters that are past there use by. Will check supply Monday. PM me if you want them. Converting to a solid is fine providing you can get them apart. Just chuck the squashy parts and make a solid replacement.
Mostly l deal with solid rollers and all Chevs, Holdens and Fords provide oil up the pushrods for rocker lube.
Normally we fit restrictors in the oil gallery on the supply side when solids are fitted.
Most currant Supercars are now using keyed Jesel lifters and all have bushed lifter bores with individual restrictors. We have just finished a 7000km Spintron test for V8SC running simulated laps of Bathurst.
This was for the new control cam they have mandated from this weekend at Darwin.
To check the oil supply window to your chosen lifter fit desired cam in block.
Remove oil gallery bung, (usually at rear) and drop chosen lifter in closest hole.
With torch peir down gallery and you should be looking at the hole lining up with the gallery.
Rotate cam by hand and make sure the hole stays in the window for a majority if not the whole rotation.
If it misses a lot you can slot the side of the lifter to give supply to the hole.
Some motors this process is not that easy and you have to do it mathmatically.
Race motor solid roller ducks guts good luck.
Chris
As for a "spintron" my brain has been in hyperdrive about all this for the last couple of weeks and I'm not sure which night at 3am it started but for the last few days I've been thinking it'd be bloody great to have a way of running the top end of the motor AND the oiling system up to 8000rpm without the crank and pistons.....that'd make this development stuff a whole lot easier.......in my dreams....
...few understand what I'm trying to do , but they vastly outnumber those who understand why..
- gennyshovel
- Posts: 866
- Joined: Tue Mar 29, 2005 10:10 am
- Location: Broken Hill
-
- Posts: 1315
- Joined: Tue Jul 05, 2005 11:23 pm
- Location: Right behind you Chief !
tolerance
Just lookin' at it T'fer ,
I reckon you need a thicker gasket between the barrel and the crankcase.....
I reckon you need a thicker gasket between the barrel and the crankcase.....
...few understand what I'm trying to do , but they vastly outnumber those who understand why..
- Greg Watters
- Posts: 760
- Joined: Mon Sep 27, 2004 8:57 pm
Re: dub
Doc i remembered why we used to space them down not up,Dr Goggles wrote:Greg Watters pointed out that if we do bung up the standard ones it would be safer to use a proper circlip in the top than the pissy hairclip they have in them....he also felt that if we used a piece of short tube that it would be better above than below the original piston.....
....
It was on Chryslers and there solid lifters were the same installed height as a bottomed out hydraulic, , if we spaced up, the adjustable rockers would be out of range without custom pushrods..
your results may differ
- ROSS BROWN
- Posts: 477
- Joined: Thu Feb 18, 2010 6:43 pm
- Location: COORPAROO BRISBANE
Don't no if you boy's realise this place exists . among other things they specialise in performance parts for V6 buick motors, blocks ,cranks, lifters and pretty well anything ya need , pricing doesnt look to bad either.
steal ya wives purse and start spending.
REMEMBER : Its easier to ask for forgivenes than for permission
www.taperformance.com
steal ya wives purse and start spending.
REMEMBER : Its easier to ask for forgivenes than for permission
www.taperformance.com
IT IS ALL A RACE AGAINST TIME.
TIME WAITS FOR NO ONE.
HOW FAST CAN YOU GO ?
S/UF 925
TIME WAITS FOR NO ONE.
HOW FAST CAN YOU GO ?
S/UF 925
The problem is that the '78-'87 Buick V6 has very little in common with our locally produced Holden V6. Alot of people refer to the early Holden V6 (VN-VR Commodore) as the "Buick" and while the same engine was used in '88-'94 Buick's there not much performance gear for them compared to the early GN-Buick type engines.ROSS BROWN wrote:Don't no if you boy's realise this place exists . among other things they specialise in performance parts for V6 buick motors, blocks ,cranks, lifters and pretty well anything ya need , pricing doesnt look to bad either.
steal ya wives purse and start spending.
REMEMBER : Its easier to ask for forgivenes than for permission
www.taperformance.com
But it's the thought that counts.
-
- Posts: 1315
- Joined: Tue Jul 05, 2005 11:23 pm
- Location: Right behind you Chief !
Movement at the station
Last weekend I bought a VN series one manual motor , that means we can lose the adapter that we have been using to mount our flywheel on the small boss "auto" crank that we are currently using. The motor looked pretty good, hadn't been tortured. We took it bolt from bolt keeping what we can use.... We'll be sending the crank off to be balanced with the flywheel and pressure plate soon.
I have also just bought a 3 litre crank from the States, after about 2012/13 we will have wrung most of what we can from this motor and intend to follow the Jack Dolan method and destroke it to F class.In a perfect world we might get over 7500rpm from it N/A......... No-one has run F/FL or F/GL yet.......Later.
The new adjustable roller/roller tip rockers arrived from the States this week too. A mate in Milwaukee has been very helpful with forwarding items from vendors who won't ship outside the country, I was quoted over 500 bucks from an outfit in Sydney for these, they came in under 300..... I have a grudging respect for artful thieves but those guys are just dumb a'holes.
The guy who sold me the manual motor has also agreed to separate an Alloytec bellhousing from an auto so I can see what size the "hole" in the front is , that way we can work out whether it is feasible to put our shortened Aussie four-speed behind the Alloytec we have.....happy now colonel?
I have also just bought a 3 litre crank from the States, after about 2012/13 we will have wrung most of what we can from this motor and intend to follow the Jack Dolan method and destroke it to F class.In a perfect world we might get over 7500rpm from it N/A......... No-one has run F/FL or F/GL yet.......Later.
The new adjustable roller/roller tip rockers arrived from the States this week too. A mate in Milwaukee has been very helpful with forwarding items from vendors who won't ship outside the country, I was quoted over 500 bucks from an outfit in Sydney for these, they came in under 300..... I have a grudging respect for artful thieves but those guys are just dumb a'holes.
The guy who sold me the manual motor has also agreed to separate an Alloytec bellhousing from an auto so I can see what size the "hole" in the front is , that way we can work out whether it is feasible to put our shortened Aussie four-speed behind the Alloytec we have.....happy now colonel?
...few understand what I'm trying to do , but they vastly outnumber those who understand why..
try this
love the never ending development story ---dont stop
we have used MyUS (a forwarding house) to get stuff from the US when biusness s wont send out side the US cost was quite reasonable
cheers
harky
we have used MyUS (a forwarding house) to get stuff from the US when biusness s wont send out side the US cost was quite reasonable
cheers
harky
harky
DLRA #643
so far 120mph for$2000---imagine how fast I can go for $20,000
DLRA #643
so far 120mph for$2000---imagine how fast I can go for $20,000
-
- Posts: 1315
- Joined: Tue Jul 05, 2005 11:23 pm
- Location: Right behind you Chief !
in the cab
bit of video from the 09 meet from inside the Spirit of Sunshine ....I think you can hear the rev limiter making it miss at about 2.00 at 5200rpm....
http://www.youtube.com/watch?v=Z3yYU1hbgjI
http://www.youtube.com/watch?v=Z3yYU1hbgjI
...few understand what I'm trying to do , but they vastly outnumber those who understand why..
-
- Posts: 1315
- Joined: Tue Jul 05, 2005 11:23 pm
- Location: Right behind you Chief !
Re: Commodore Valuables
I went up to Norm's this week finally to pick up the diff parts that came back from Bonneville in their container, sadly I didn't have much time on my hands to chat but suffice to say it's always good seeing inside that shed. I'm not a huge fan of the licked clean billiard room style sheds that people are always raving about.....I get more of a buzz out of the crammed full ,shit all over the place types....there's good stuff everywhere you look at Norms once you've actually worked out how to get in there.....
here is the Torsen centre....
and here is a tiny little 2.14:1 set
Bill " Sparky" Smith had mustered the parts we needed to put together a 7.5 inch ten bolt series two Torsen centred rear end . Sparky has run a record over 300 with a 900hp big-block with one of these diffs.They come ,most importantly ,with ratios that go from 3.08,( 2.92 I think) 2.73, 2.56, 2.41 2.28 and 2.14:1 ....we got the 2.73, 2.41 and 2.14:1 sets with it and are trying to get a 2.56. Something in my bones tells me that our "sweet spot" will be somewhere between the 2.56 and the 2.41 .
This year we ran 193 with a 2.77 ~ (2.77/2.41) x 193 = 221.83mph
...however as we were only putting on 12mph/per mile last year I figured we were going to need more power to pull a lower gear set.......otherwise the only difference in our figures when we hit the last clock would be that our revs would be lower
Since I last posted we have collected the new Wade 1644a cam......pictured here up against the stock series one cam...no prizes for picking the new billet
This week I also picked up the forged stainless LS-1 style roller tip roller rockers that I bought from the States. Steve Angelovski from MACE Engineering parted them, swapped them to ecotec style needle bearings and made a pedestal base plate so as to fit them to our series one heads....
as they came.....
with the new needle roller bearings....
and sitting on the freshly fabbed pedestal plate to fit them to the series one heads...
Last weekend I got the gasket set and a brand new harmonic balancer.....the Colonel reckons the 300,000k balancer we were using had a groove in it worn by the timing cover seal that was likely the cause of our oil leak. Those rotating bits are going to Hastings to be balanced this week..........aren't they Colonel.
here is the Torsen centre....
and here is a tiny little 2.14:1 set
Bill " Sparky" Smith had mustered the parts we needed to put together a 7.5 inch ten bolt series two Torsen centred rear end . Sparky has run a record over 300 with a 900hp big-block with one of these diffs.They come ,most importantly ,with ratios that go from 3.08,( 2.92 I think) 2.73, 2.56, 2.41 2.28 and 2.14:1 ....we got the 2.73, 2.41 and 2.14:1 sets with it and are trying to get a 2.56. Something in my bones tells me that our "sweet spot" will be somewhere between the 2.56 and the 2.41 .
This year we ran 193 with a 2.77 ~ (2.77/2.41) x 193 = 221.83mph
...however as we were only putting on 12mph/per mile last year I figured we were going to need more power to pull a lower gear set.......otherwise the only difference in our figures when we hit the last clock would be that our revs would be lower
Since I last posted we have collected the new Wade 1644a cam......pictured here up against the stock series one cam...no prizes for picking the new billet
This week I also picked up the forged stainless LS-1 style roller tip roller rockers that I bought from the States. Steve Angelovski from MACE Engineering parted them, swapped them to ecotec style needle bearings and made a pedestal base plate so as to fit them to our series one heads....
as they came.....
with the new needle roller bearings....
and sitting on the freshly fabbed pedestal plate to fit them to the series one heads...
Last weekend I got the gasket set and a brand new harmonic balancer.....the Colonel reckons the 300,000k balancer we were using had a groove in it worn by the timing cover seal that was likely the cause of our oil leak. Those rotating bits are going to Hastings to be balanced this week..........aren't they Colonel.
...few understand what I'm trying to do , but they vastly outnumber those who understand why..
Re: Commodore Valuables
Doc
get all the crank parts balanced seperately so if necessary you can change individual parts.
The ballancer won't like it but if you change say a flywheel and it's not done you will need to strip the motor to do everything as a set again
Doc could you pm me your ph no. I should be in Melbourne on 6 Dec
cheers Bones
get all the crank parts balanced seperately so if necessary you can change individual parts.
The ballancer won't like it but if you change say a flywheel and it's not done you will need to strip the motor to do everything as a set again
Doc could you pm me your ph no. I should be in Melbourne on 6 Dec
cheers Bones
-
- Posts: 1315
- Joined: Tue Jul 05, 2005 11:23 pm
- Location: Right behind you Chief !
Carnage
Pistons aren't supposed to look like this are they?
This used to be the rear main bearing
Somewhere there is the explanation as to why I was having a little trouble seeing with all the vibration that was going on.... So, we're off to buy some bearings , and some pistons........In the meantime there's a brand new Alloytec on eBay so we can pay for some parts...
This used to be the rear main bearing
Somewhere there is the explanation as to why I was having a little trouble seeing with all the vibration that was going on.... So, we're off to buy some bearings , and some pistons........In the meantime there's a brand new Alloytec on eBay so we can pay for some parts...
...few understand what I'm trying to do , but they vastly outnumber those who understand why..
- Last Minute Racing
- Posts: 118
- Joined: Sun Mar 04, 2007 1:20 pm
- Location: Adelaide Hills DLRA#928
Re: Commodore Valuables
Coopers Sparkling Ale long neck with a cork in it??
Nice looking bits from the States BTW.
Thanx
Dave
Nice looking bits from the States BTW.
Thanx
Dave
FASTER! FASTER! BANG F&^*K! F%&*K! F#$%K! s*** MORE MONEY
- ROSS BROWN
- Posts: 477
- Joined: Thu Feb 18, 2010 6:43 pm
- Location: COORPAROO BRISBANE
Re: Commodore Valuables
.........Dr Von Sunflower Googles.....
Guna have to stop breeding them Nazies with dem Hippies..
Guna have to stop breeding them Nazies with dem Hippies..
IT IS ALL A RACE AGAINST TIME.
TIME WAITS FOR NO ONE.
HOW FAST CAN YOU GO ?
S/UF 925
TIME WAITS FOR NO ONE.
HOW FAST CAN YOU GO ?
S/UF 925