Honda MG & MF 750
Moderator: DLRA
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
Re: Honda MG & MF 750
Put on the pistoles today, barrels and head.
I machined the wrist pins from 56mm back to just under 53mm as per JE piston instructions to the thou, but no way could I get the circlips in so I machine another .035 thou off to leave me with about .015 thou end float between the locks, I checked the stocky's and they were about the same.
will leave the engine overnight and retension each head nut tomoz............and a bit for the road.
I tried one of those MLS gaskets this time, see how they go. Man those Honda rings were a delight to insstall compared to those skinny arsed JE rings
It was so easy I done the install by myself, couple of screww drivers, just let the weight of the barrels ease on down at my pace. Long live Honda
getting closer Finny
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
Re: Honda MG & MF 750
The ol build forum is a bit quiet, just wondering if anyone else is going to the salt this year ?
Re: Honda MG & MF 750
Hey Johno, yep Im waiting on some new pistons, just did some mods to my clutch. Few other things on the go. Should add to my build diary.
Dave
Dave
Last Minute Racing
DLRA #928
2010 MPS/G 250 118 MPH
2011 Washed Out
2012 Washed Out
2013 MPS/G 250 131 MPH (RECORD)
2014 MPS/G 250 140 MPH (RECORD)
2015 MPS/F 250 DNF
2016 MPS/F 250 114 MPH (RECORD)
2017 MPS/F 250 DNF
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
Re: Honda MG & MF 750
I have been doing some serious planning as the carbs on a mock up interfeared with each other .
My plan was to make 4 small bends about 5 deg to splay the carbs apart and the bonus was If I made them 50mm long I wouldnt need ram tubes,
Also I needed 32 mm ID but the closest is 34mm ID, when bending 5 deg in the mandril it shrunk the 34 back to 32, cool hey
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
Re: Honda MG & MF 750
Last Minute Racing
DLRA #928
2010 MPS/G 250 118 MPH
2011 Washed Out
2012 Washed Out
2013 MPS/G 250 131 MPH (RECORD)
2014 MPS/G 250 140 MPH (RECORD)
2015 MPS/F 250 DNF
2016 MPS/F 250 114 MPH (RECORD)
2017 MPS/F 250 DNF
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz
Re: Honda MG & MF 750
Re salt wash down after run ,
Has anyone tried this ol wives tale ?
Bucket, 2 tablespoons baking soda, 2 tablespoons of dolopril limestone OR granual gypsom, half cup of auto wash, half gallon water, mix with gloves on and spray vehicle with an old water fire extinguisher
Love to know if it works ?
Has anyone tried this ol wives tale ?
Bucket, 2 tablespoons baking soda, 2 tablespoons of dolopril limestone OR granual gypsom, half cup of auto wash, half gallon water, mix with gloves on and spray vehicle with an old water fire extinguisher
Love to know if it works ?
-
- Posts: 260
- Joined: Mon May 21, 2012 12:17 am
- Location: Berri Sth Oz